Uncategorized

Create a Neck Cuff for your Art Bead

Sometime last summer, I began going tribal. I was very inspired by the National Geographic show and recorded all the past episodes of Going Tribal to watch several times. One of the details that caught and held my attention were the neck cuffs that were fashioned in rudimentary ways. The cuffs on the different tribes featured on the show had a common denominator in that they held a special charm or talisman that meant something to the wearer. Some of the neck cuffs had collections of several “charms”, others were simple with one or two hanging in the center.
 
 A light bulb idea! What if a neck cuff could be hammered out to feature a special Art Bead? I’d never made a neck cuff before but I had already hammered out a heavy gauge bangle, how much harder could it be?

 I was surprised by a couple of things; 1 – You do not need a steel neck mandrel to curve the wire. Sweet! This saves you at least $60 bucks! And 2 – they are surprisingly comfortable to wear. In fact, they bring to the surface a wild feeling inside that has been smothered by years of proper society upbringing.

What you do need;
Bench block – or other hard surface to hammer the wire against, even wood could work.
Hammer – my favorite hammer to use was found in my grandpa’s old tool chest.
Flexible measuring tape – something that measures over 18 inches would be most helpful.
Heavy Gauge Wire – Copper, brass or sterling silver, dead soft, 14 gauge keeps its shape very well after hammering. You will need to make sure the Art Bead will slide over the wire before curving the wire.
Flush cutters – Heavy duty wire cutters to cut through your 14 gauge wire
Chain nose pliers – you will need a good pair of wide, chain nose pliers to firmly grip the wire as you shape it.
Round nose pliers – optional, you do not need a perfect loop formed for your latch 
Medium jewelers file – I use a dremel with a sanding drum bit to save time and work but a medium rasp jewelers file is an inexpensive way to smooth the edges of your cut wire.
Sharpie pen – to mark measurements on the wire

Begin by measuring  your neck where you would like the neck cuff to lie. To create a neck cuff that latches, you will need to cut that measurement plus 3″ from your heavy gauge wire. File the cut edges smooth with your jewelers file. Hold the file at an angle as you run its length down the cut edge of the ends.

To curve the wire into a rounded, oval neck cuff shape, hold the middle of the wire in your left hand and tap the hammer on the end of the wire over the bench block with a straight up and down motion. Gradually move the hammer up towards the middle of the wire as you gently move the left hand up. The wire will begin to curve in as you hammer.

Once you reach the middle of your wire, slide on the Art Bead and switch sides so you are holding the curved side in your left hand now and hammering the straight side against the block. Repeat the same motion as previously so this side of the wire curves in also. You can create a sharper bend in the middle of the neck cuff by pushing in on both sides of the ends.

Once the curve is to your liking, measure 1″  from one end of the curved wire, mark this measurement with a sharpie pen. Grip this mark with your round nose pliers and bend the end of the wire towards the middle of the neck cuff to form a curve. Press in with the chain nose pliers to complete the loop. This will be the side the latch hooks into.

The other side of the neck cuff can be curved in at 1″ to form a simple latch. If you grip the latch in your chain nose pliers and turn it slightly to the side, it will easily slide into the curved loop, creating a secure clasp that will stay closed while the piece is being worn. The amazing thing is; you do not even feel the latch at the back of your neck!

My special clay Art Bead was a gift from the talented and most gracious Barbara Wukich, whom I would link you to but she does not sell online. It’s special meaning is accented by the rattles inside the fired clay. This unique bead required a necklace that is as rustic and primitive but did not over power it. I choose to hold it in place on the neck cuff with strips of recycled sari silk and bound wire. A simple tassel of more silk, patina-ted chain and organic shaped bits of metal are hung next to the bead to add to it’s wild, tribal charm.

Now I just need a place to wear my tribal neck cuff! I hope you are encouraged to hammer out your own neck cuff from these instructions, I think you will be surprised at just how easy it is.
Much Love & Respect,
Shannon
MissFickleMedia

You Might Also Like

Previous Story
Next Story

21 Comment

  1. Gardanne
    April 29, 2010 at 12:48 pm

    Thanks Shannon, good idea for my big hole beads. Love the silk and wire to hold it in place, just got some sari silk the other day.

  2. Lorelei
    April 29, 2010 at 1:04 pm

    This is fabulous!!! Thanks for sharing the technique!

  3. Julianna Cannon
    April 29, 2010 at 1:20 pm

    Absolutely stunning! Love it.

  4. Michelle
    April 29, 2010 at 1:34 pm

    Thanks for the technique. The necklace is FABULOUSly wild!
    Bead Happy!
    Michelle

  5. mairedodd
    April 29, 2010 at 2:25 pm

    shannon, i have been sitting here trying to think of the 'i need tos' for the day – and thanks to you i now have an 'i have got to!' filled with enthusiasm… i have a bead that i hadn't quite figured out what to do with and now i know! she needed a tribal type setting and i love this idea! thanks for sharing this wonderful project –

  6. Jan Vermillion-Thomason
    April 29, 2010 at 2:30 pm

    i love this – and i am so appreciative of you for sharing how to make it.
    i do have one question – did you patina the 14 gauge wire with the patina solution or some other way?
    thanks,
    jan
    [email protected]

  7. Veganosaurus
    April 29, 2010 at 2:46 pm

    You have not only inspired me to make some neck cuffs but also to make a series of art beads to display on these. 🙂 Thank you!

  8. Evie's Tool Emporium
    April 29, 2010 at 3:09 pm

    I couldn't wait to see the final necklace-I had to jump ahead!
    Love the tribal look!

  9. Jeannie
    April 29, 2010 at 3:27 pm

    Hey Shannon How fugel of you. I'm digging the necklace and I especially like the sari silk. Thanks for taking the time to put this tutorial together and sharing it with us.

  10. missficklemedia.com
    April 29, 2010 at 4:51 pm

    I am so glad everyone likes it! I know it is a bit different, but some beads require something with a bit more savagery!

  11. ladynoble
    April 29, 2010 at 4:57 pm

    Love this! Thanks for sharing the technique!

  12. TesoriTrovati
    April 29, 2010 at 5:12 pm

    What an awesome way to display something so special! I always seem to take it over the top with my designs so I really appreciate the impact this has when it is so simply stunning. Great job Shannon! Thanks for sharing your inspiration. Enjoy the day! Erin

  13. Cerulean Gypsy
    April 29, 2010 at 5:18 pm

    Shannon,
    Blast you. I had plans today to work in the yard. Now I'm going to have to actually use the huge rolls of 14g and 10g copper wire I've been staring at for the last 6 months. Thank you for lighting a fire under me. Your piece is beautiful and an inspiration.

  14. SharonP
    April 29, 2010 at 7:38 pm

    Thanks for sharing your great idea-I can't wait to try it!

  15. Christina Allen Page
    April 30, 2010 at 1:36 am

    Fantastic!

  16. Jen V.
    April 30, 2010 at 4:07 am

    I love this idea! And your "sample" is gorgeous! I'll have to figure out a few beads to honor this way myself! Thanks so much!

  17. Alice
    April 30, 2010 at 12:06 pm

    What a beautiful way to show of art beads, and connect with our wild side at the same time!

    Thanks for the inspiration!

  18. Mary Ann Carroll
    April 30, 2010 at 2:00 pm

    I LOVE it!!! That is sooooo cool!!

  19. Cindy Lietz, Polymer Clay Tutor
    May 1, 2010 at 1:22 am

    Gorgeous neck cuff Shannon! I love how you embellished the front. So Missfickle!

  20. Barbara Lewis
    May 1, 2010 at 11:18 am

    This is great, Shannon. I saw Maire use of the technique on her necklace and I thought, "Wow, this would be a great form for my enameled beads!" Thank you.

  21. Joy
    May 4, 2010 at 6:59 am

    Very inspiring!! This may be just what this big Trey Cornette bead I've been holding on to needs! Thanks for sharing!

Comments are closed.